As an AI language model, I can give you a comprehensive guide on how to take apart Litter Robot Globe. Before tackling this process, make sure that you read the manufacturer’s instructions carefully and check for any warranty issues.

The litter robot is one of the most popular automatic self-cleaning cat litter boxes available in the market. It features state-of-the-art technology, including advanced sensors and a unique waste disposal system.

However, if your Litter Robot Globe stops working correctly or needs repair, it may be necessary to disassemble it completely. But don’t worry; it isn’t as complicated as it seems! By following these easy steps, you’ll have your Litter Robot Globe taken apart in no time:

Step 1: Unplug and Empty

Step 1: Unplug and Empty

Before starting any work on your Litter Robot Globe, make sure to turn off and unplug the unit entirely. Then remove the waste drawer from beneath the globe and empty out all litter clumps improperly disposed of.

Step 2: Remove The Bonnet

Step 2: Remove The Bonnet

The next step is removing the bonnet (the plastic cover at top) covering your Litter Robot’s motor internals below. Start by pushing down both shiny knobs on either end of this part using some pliers over them before turning counter-to-clockwise slowly until their release with slight force to avoid breaking off brittle small tabs holding them onto edges underneath tightly also;

Make use of flat-nosed pliers once again over another knob positioned inside towards front-center area till loosening up fully enough away so that entire piece could lift freely from globe base section via back-end first being gently tilted upwards during removal routine too far forward could result in breaking fragile plastic clips holding assembled parts together firmly.

Step 3: Detach Other Parts From Base

After removing bolts securing claw-shaped linkage/support arms between lower bottom area inside main body shell made of heavier grey material along front/back sides (located close side guards), push down on front section (claw end) checking clearance between robots’ plastic parts along with pushing outwards in gentle circular motion until revealing space onto unit’s bottom layer entirely blocking visibility.

Now you will need to unscrew four screws located around the edge of the globe base from below and unplug excess cords attached to motor internals via mainboard. If possible, you can also remove both side guards by prying them loose from their place working edges first then moving towards center section where they connect before tilting guard upwards during removal routine for better access below another plate/layer holding up second motored assembly operating alongside primary one already disengaged earlier on.

Step 4: Removing The Waste Drawer Assembly

Next, it’s time to remove the waste drawer assembly that houses all your cat’s litter clumps after every cycle has been completed inside Litter Robot Globe unit. The best approach is sliding drawer slightly downwards while lifting off mesh screen using pliers over its sides if needed but make sure not to damage delicate wires attached underneath or any sensors closeby nearby slots made specifically for this purpose.

If there are persistent stains on any surfaces observed inside here leading outside housing bodyshell upon thorough inspection visually, clean each part separately ensuring no moisture gets trapped anywhere which could hinder function properly even after reassembly done later on too.

Step 5: Disengage Gear Motors

The final step is disconnecting gears from within gearmotors driving Litter Robot Globe performances overall; unscrewing couple bolts keeping each tumbler piece firmly held onto rods threaded through gearmotor pieces previously disconnected now freely spinning independently again when not under tension since they keep rotating clockwise/anti-clockwise movements alternatively whenever engaged anymore due zero force applied thus virtually causing no turning at all necessitating intervention as described above was required earlier already nonetheless necessary anyways 🙂

Once you’ve taken apart all these components completely and organized them adequately somewhere safe( we suggest placing everything into different sorting boxes if possible using labels indicating their purpose/origin so that no confusion occurs when you need to reassemble the Litter Robot), it’s time to start rebuilding the Globe.

Reassembly

The following steps will help you reunite all of your litter robot components and save you from purchasing an entirely new unit due to piece by piece restoring old one thereby getting back its former efficiency without breaking bank unnecessarily:

1. Attach supports claws onto base shell immediately once noted during disassembly where each belonged.
2. Place bonnet over some attached cords black/hot green colored outfacing downwards to avoid potential smash experiences later on too mid-center slot aligned screw heads backs fine-tuning loose ends properly before tightening down securely in place.
3. Put side guards into position like earlier with screws through holes lining them correctly, externally located based under hindquarters while sticking outside protective plastic cover section beneath connected during installation process which also has bolts embedded into counterparts situated opposite along bottom edges rearwardly left/right as required before attaching this plate underneath again via two similar looking connector metal prongs absent on front level positioning points screwed firmly together being careful not breaking any clips holding units firmly in contact against their respective sides here whilst still connecting wires ever so gently later when reinstallation finalizing process begins alongside other smaller assemblies performed simultaneously or independently designed purely for diagnostic purposes similarly coming out quite easily requiring very little pressure applied leading successful outcomes only even compared slightly more complex mechanism used elsewhere yet failing testing procedures conducted regularly over those periodical maintenance programs recommended mostly online and offline spreading messages about taking correct preventive measures avoiding costly replacements though verifiable statistics available backing up its effectiveness apart from numerous reliable testimonies confirming aforementioned events had occurred already quite frequently above-average lifespan supposed otherwise amongst competitors besides innovative technology behind our proud achievements constantly ranked higher than others 🙂
4 . Reattach waste drawer assembly lid mesh-based top-side secured tightly enough against spills or leaks occurring whenever liquid substances present within disrupting cycle routine leading unclean malfunctioning situations sometimes even becoming permanent, if not maintained properly.
5. Finally, re-attach two gearmotors drive tumblers operating cleaning procedures systematically simultaneously doesn’t matter which order initiated first or last provided aligned correctly axles located at both ends inserted adequately without forcing them in too tightly( been known to break off some occasions due sudden force applied ) otherwise could cause damage requiring further intervention as before.

Conclusion

In conclusion, taking apart your Litter Robot Globe isn’t difficult at all if done with care and attention to detail. By following the steps above carefully, you’ll be able to disassemble every component of your litter robot globe successfully!

Remember: If you’re unsure about any step along the way or feel like something isn’t making sense, don’t hesitate for a second seeking professional assistance from customer support specialists who are always available online or through a phone call only happy helping out fellow cat owners experiencing similar problems with their beloved purring friends 🙂